The real output of automatic screwdriving equipment depends on whether screws can be fed continuously, accurately and with minimal jamming — not on the single-screw speed of the tightening tool.
1. How Does Automatic Screw Feeding Affect the Efficiency of the Whole Line?
Automatic Screw Feeding (Automatische Schraubenzufuhr) sorts, separates and delivers loose screws to the fastening workstation. The entire line chains together sorting, screening, distribution, conveying, arrival confirmation and final tightening — if any single link is unstable, the whole machine slows down.
The Danikor Step Feeder (der Stufenförderer) uses a step-lifting mechanism to raise loose screws gradually into the downstream sorting, distribution and conveying stages. There is no vibration in the feeder tank and no friction damage to the screws, so feeding is more reliable. Paired with a Feeding Tube (der Druckluftschlauch für die Schraubezufuhr) that is "flexible on the outside, rigid on the inside" — wear-resistant yet pliable, and adaptable to workstation layouts — it delivers stable feeding.、

2. Which Conditions Require Feeding Stability First — and Which Are Not Suitable for Automatic Screw Feeding?
When feeding becomes the bottleneck — Screw Jamming (Verkant), deviated screws or abnormal screws causing stoppages and manual handling — stability must take priority. For multi-spindle tightening or multiple workstations sharing one supply system, size for the peak demand of concentrated screw pickup, not just the average feed speed.

The Danikor Step Feeder achieves a Screw Jam Rate (Verkantrate) of 50 PPM on standard screws. A low Screw Jam Rate reduces manual intervention and keeps feeding and tightening continuously connected. However, the Screw Jam Rate is not a fixed value: it is affected by screw shape, dimensional consistency, surface condition, the conveying line and maintenance.
Important limitation: If the incoming screws are mixed with different lengths, deformation or burrs, and these cannot be identified first, automatic screw feeding is not suitable. Abnormal screening must be completed before the screws enter the feeder.
3. Are Tightening Speed and Feeding Stability the Same Thing?
No. Tightening speed only measures the Cycle Time per Screw (Einzelzyklus) of a single fastening, while feeding stability looks at whether screws arrive continuously and without interruption. If the feeding cycle cannot keep up, the Smart Tightening Tools (Intelligenter Schrauber) sit idle waiting for screws.
Handling a jam also consumes time for confirmation, clearing, reset and restart. Without buffering or upstream/downstream interlocks, a local abnormality can spread to neighbouring equipment. Abnormal screws (mixed lengths, deformation or burrs), even if delivered, can still cause assembly specification errors. When feeding is already the bottleneck, reducing the frequency of interruptions is more valuable than compressing a single tightening cycle.
Selection criterion
First run continuous trials with your actual screws, define the jam-counting method and acceptance criteria, and confirm that the feeder's Screw Jam Rate (for example, 50 PPM on standard screws) and abnormal detection capability meet the requirements. Only then discuss tightening cycle time — if feeding is unstable, speed is meaningless.
Frequently Asked Questions
Q: How can you tell whether automatic screw feeding is suitable for your application?A: Run continuous trials with your actual screws first, and define the jam-counting method and acceptance criteria. If the incoming screws are mixed with different lengths, deformation or burrs, abnormal detection and screening must be completed before automatic screw feeding is introduced.
Q: What is the Screw Jam Rate of a Step Feeder?A: The Danikor Step Feeder achieves a Screw Jam Rate of 50 PPM on standard screws. There is no vibration in the feeder tank; a step-lifting mechanism raises the loose screws gradually for the downstream sorting, distribution and conveying stages, without friction damage.
Q: How do you size a feeder when multiple workstations share one supply system?A: For multi-spindle tightening or multiple workstations sharing one supply system, calculate the peak demand for concentrated screw pickup rather than sizing by average feed speed alone. This prevents the tightening tools from waiting because the feeding cycle cannot keep up.
Q: Does the Screw Jam Rate change from one site to another?A: Yes. The Screw Jam Rate is not a fixed value; it is affected by screw shape, dimensional consistency, surface condition, the conveying line and maintenance. The real value of a low Screw Jam Rate is fewer manual interventions and a continuous link between feeding and tightening.
Q: What problems can abnormal screws cause?A: Screws mixed with different lengths, deformation or burrs interfere with distribution and conveying; even if delivered to the workstation, they can cause assembly specification errors. Detectable abnormalities must therefore be identified and handled before the screws enter downstream processes.